How To Replace Front Wheel Bearings - You Can Do That
Posted: Sunday, May 28, 2006
by Dennis Watson
Zeoh.com Free Classifieds
Recently the right front wheel bearing went bad on my 2002 Mazda 626. Apparently my oldest daughter hit a large pot hole bending the wheel and damaging the wheel bearing. I noticed a slight hum in the front end with a slight shutter as well, I thought that the tires needed to be balances and rotated, so I took it into the shop to be checked out. Well to my surprise I was told the bad news and what was worse was the amount they wanted to charge - over $500 to fix bearing and to replace the wheel. That is when I decided to do it myself.
Things you will need:
Large adjustable wrench, Channelocks, Bearing race driver tool, Various size punches, Socket and ratchet set, Assorted wrenches, A rags or two, New wheel bearings, Wheel bearing grease, New cotter pin, New grease seals, Wheel blocks, Safety glasses, A jack and a pair of jack stands.
Even if the bearings are not making a noise it is always a good idea to have them inspected every 30,000 miles. I have it done when my breaks are replaced.
Okay let's get started.
Get all of your tools and supplies together before you begin and allow plenty of time to do the job.
Please take note that these are general instructions and consult the appropriate repair manual for your vehicle.
Always think safety first whenever you're working around machinery. Wear safety classes to protect your eyes and beware of hot objects, sharp items and hazardous materials. It is very, very important to never work on a car that is only supported by a jack, always place a sturdy foundation under the vehicle to prevent it from falling on you.
From this point on cleanliness is important. You do not want any dirt, sand or metal chips inside the hub.
1. Remove your disc brake calipers and caliper bridge to remove the rotor.
2. Remove the bearing cap. This is a press fit and to remove it grab it with your channelocks and work it back and forth until it pops off. Be careful not to crush it.
3. Once the cap is off you will see a cotter pin, remove the cotter pin and remove the retainer ring. If your vehicle has a castellated nut, you will not have a retaining ring.
4. Using your channelocks or adjustable wrench, remove the nut from the spindle.
5. Next remove the outer wheel bearing and washer.
6. Slide the rotor or drum off the spindle.
7. Remove the grease seal and take out the inner wheel bearing.
8. Wipe all the old grease from inside the hub.
9. Remove the bearing races from the hub.
10. Take a punch with a flat narrow tip and place it on the back of the race.
11. Tap the race out, alternating from side to side so it comes out evenly and doesn't get cocked in the hub.
12. Once it's out, flip the rotor or drum over and do the same for the other race.
13. Clean the inside of the hub with some rags.
14. Make sure the spindle is clean as well.
That's all there is to it. Like I mentioned earlier take your time and you will not get frustrated, good luck with your project.
Copyright 2006 Dennis Watson
--------
Dennis Watson - Just helping others succeed.
Zeoh.com Free Classifieds Web Site => http://www.zeoh.com/
This Article has been viewed 21,109 times. (Not updated in real-time.)
Top-level comments on this article: (6 total)This guy is wrong Mazda 626 is a press in WB. They do not "drop out" and there is no inner and outer
You need a hydraulic press to press the bearings in and out. Period.no you dont i am a 37 yr woman and did my rear bearings on my geo it took less then 30 min to pop out the bearing and to pop in the new i used a socket and a hammer.The Time and equipment need to replace hub bearings varies by make and model. Some will need a press, some will not. Some will need an entire hub assembly, some only need the bearing. BTW I suggest USA made Bearings from MIBearings LLC
You do need a hydraulic press to get the bearings out for most cars and trucks, i think. I suggest that you get your bearings from MIBearings LLC , they are USA made. google it!
You are all right and wrong. If the bearings are pressed you have to have them pressed in and out w/ a hydraulic press...meaning you will need to take it in. If they are not you will know, the will come out with little effort depending on how old they are. They can be put back in by hand also. You also might have sealed bearings which is completely diff story.
How do you replace the cv axel on a 2000 mazda mpv
I followed this to change the front bearing on my mazda demio but this description misses the need to calculate the shims with a special tool. as a result i've destroyed the new bearing and had to go cap in hand to the main dealers
We want your comments! If you can read this, you don't have javascript enabled, so you can't use this comment system. Please enable javascript.